Joined in 2023 
82 
63 About this deal
The payment systems used by Di Vapor are based on industry standards to ensure all payments are securely handled.
How to Install a Shower Tray | Victorian Plumbing How to Install a Shower Tray | Victorian Plumbing
Stylish and functional, this shower waste will effectively drain out your wastewater, giving you a clean and hygienic shower area every time. Once the tile adhesive had cured correctly the battens were removed leaving roughly a 2 inch gap that we could then tile once the ray was fully in place. The final thing you need to do is take a good quality silicone sealantand carefully seal around the edges of the tray, creating a bond that will keep everything sturdy. If your shower tray is a long way from the external wall (where the waste pipe needs to go) and the waste pipe will have to be threaded through several joists due to their orientation, then it may be worth raising the tray up and running it above the floor. Sometimes it will be necessary for the shower tray to be lifted off the floor to ensure that the waste waster runs away downhill to the nearest drain point.To fix your shower tray firmly to the floor, the best stuff to use is a strong construction adhesive. You will also learn about how to repair any damage before installing your new shower tray, how to connect up wastes and then how to seal a shower tray correctly to prevent any leaks. Once in place, all levels were then checked to make sure the tray itself was totally flat and level. That being said though, if it’s a new install and you have to get a full waste pipe in place to carry water to the main drain, this may be something you can do along with the rest of the work.
Low Profile Shower Trays - Stone Resin Shower Tray Low Profile Shower Trays - Stone Resin Shower Tray
In general, if you are installing on to a floating timber floor, a flat low profile tray is the way to go as the flat base will provide great support for the tray and also access to the underside of the tray for the waste should be fairly straight forward as you can simply cut a hole in the floor.The tray is then dropped into position, levelled and effectively glued into place and the trap is connected to the tray (the trap is already attached to the pipe as you have seen). It also takes longer to do and is more expensive, though steps can be taken sometimes to mitigate the risk (by reinforcing the floor in other ways when possible. Mark out where the tray is going to go and replace any floorboardsin this area with marine plywood that is at least 18mm. Use your sealant gun to force the sealant into the joint so that it’s fully filled and then dampen your finger and run it over the surface to both smooth it off and force it fully into the gap. Before you start, you need to make sure that the floor beneath the tray is capable of supporting it.
Low Profile Shower Trays | Showering | Screwfix
Using some suitable sanitary silicone, run a bead around both edges of the tray that butt up to the wall and then dampen your finger and use it to force the silicone down into the joint and then leave to cure. They’re made from a really tough acrylic capped stone resin which means they’ll easy put up with the day to day use that a shower tray gets, and the smooth surface feels great on your feet!Firstly, place the tray loosely where you want to eventually install it to check for any fitment or clearance issues.
Wirquin SLIM+ Extra Flat Shower Waste 90mm - Chrome Plated
After removing the old tray it was found that a long term leak had caused a fair amount of damage to the walls and floor that would all need to be replaced before the new tray was installed in place. The wondrous, innovatively designed, Fast Flow Shower Waste from Nuie is a practical bathroom utility. As we have mentioned installing a new shower tray with the waste in the same position as the old one should minimize potentially a great deal of work. With the tray in place and floor back we’re now on the home straight, all that’s left to do now is to seal everything up and finish off.See the description below for alternatives or scroll down this page and see the associated 'Other items'. Before we go any further, you need to know whether you’ll fit a height adjustable tray or a low profile one as their installation methods will differ slightly. As we had to replace most of the floor area that the tray would be sitting on, this gave us the opportunity to ensure that the floor would be totally flat and level for the tray to sit on. Lay the base down on the floor and push it back in to position against the wall, ensuring the waste trap is sat nicely down in its hole and then allow the adhesive to cure for the manufacturers recommended time.
Great Deal 
New Comment