Hasbro NERF N-Strike Recon CS-6

Product Information

Hasbro Inc. Recalls to Repair Nerf Blasters; Child's Skin Can Get Caught in Plunger of the Toy (Article). Hasbro. Archived from the original on 2008-10-12.

The Recon has had four direct successors: the 2012 N-Strike Elite Retaliator, the 2015 N-Strike Modulus Recon MKII, the 2019 N-Strike Elite Recon CQ-12, and the 2021 N-Strike Modulus Recon MKIII. In 2019, the Recon MKII was re-released as the N-Strike Elite Recon CQ-12. This included new accessories and had a new, blue color scheme.

35 Comments

Step 1: Remove the bolt sled and plunger from the blaster. Unpin the plunger assembly from the bolt sled using a nail, small screwdriver, or punch. You can do this by inserting the nail, screwdriver, or punch into the hole that houses the retention pin and apply pressure. (Pic. 1-2) The Recon CS-6 features a reverse plunger plunger system. Because of this, it is usually disliked in modding communities. The 2008 version of the blaster notably has a shorter plunger tube, due to the 2008 product recall and redesign of the plunger. The O-ring seal on the plunger tubing makes sure that the air compressed by the plunger assembly and spring does not leak out during compression. Some blasters come with an excellent O-ring seal, while others come with undersized or loose O-rings. Improving this seal is an easy mod that can add a few extra feet to your shots. Lastly, the hand guard on the new version is narrower to provide additional space for protrusions from larger clips. This creates a noticeably shorter sloped section at the bottom of the hand guard. Make sure the blaster is de-primed by pulling the trigger and pushing the priming slide all the way forward.

Today I am going the show you how to do basic all-around beginner--intermediate modifications in the Nerf Recon CS-6In the first part of this 'ible I will show you how to do some mods for beginner modders, people who are doing something like this for the first time. Step 2: Remove screws. Be sure to make note of each screw's placement, because sizes differ. It is helpful to place the screws on the table in their original positions relevant to an outline of the blaster. There are a total of 15 screws. (Pic. 2) Alpha Trooper CS-18 • Barrel Break IX-2 • Barricade RV-10 • Deploy CS-6 • LongStrike CS-6 • Rapid Fire AS-20 • Spectre REV-5 • Stampede ECS The pre-recall Recon had an exposed plunger, which had the word "ARMED" written on the side and served as a priming indicator.

The Kohls-exclusive Recon CS-6 Special Edition includes a Recon, as well as two additional six dart clip and twelve more Streamline Darts. The air restrictor (AR) slows down the flow of air from the plunger to the dart. This device serves to reduce the blaster's power and prevent the plunger from slamming into the plunger tubing at full speed, drastically reducing the noise generated during firing. Step 2: Use gloves to hold the plunger tube and drill from the end that has the O-ring. It will take considerable pressure to get the bit to catch the plastic. Wearing a glove will prevent you from suffering a burn on your hand, should the bit catch the tubing and start to spin. (Pic. 4)Remove the two screws in the top of the priming slide, as in picture five. Do not remove the slide pieces yet.

NERF Official (2016-04-04). NERF - 'Modulus Recon MKII' Blaster Files: Inspiration (Video). YouTube. A modded blaster can shoot further and with more intensity compared to FOF (fresh out of factory) blasters. It can give you the upper hand in your next battle.There are a couple of small differences between the original, older blaster that was recalled and the newer, updated blaster that can be used to determine which version is which. The Recon MKII was inspired by the N-Strike Retaliator [2], making it a successor of sorts. In part, and perhaps due to its name, it may also be considered a successor to the N-Strike Recon CS-6.