Joined in 2023 
82 
63 About this deal
Cleaning the filter on your vacuum cleaner at least once a month is recommended to ensure that there is no loss of performance and it is still collecting all of the tiny particles that it is made to do. Additionally, if you’ve made the mistake of washing your Henry vacuum’s filter with water, then you’ll probably need to replace it. Once dust and dirt become mud inside the filter, it’s virtually impossible to remove.
When it came to the hard floor test I had a choice of two main floor brushes. The ‘universal’ brush head comprises a simple surround of stiff bristles that can be retracted for carpet use – this is the head you will use the most if your home has a mixture of hard floor and carpet since it’s easy to simply stamp on the large retractor switch as you change surfaces. Vacuum cleaners are unhygienic machines! Make sure you wear gloves when cleaning a filter to keep your hands clean. You may also want to wear a face mask to avoid breathing in dust and other small particles. Step 3: Vacuum Both Sides of the Filter I measured the raw power of the Henry Allergy HVA160 at a massive 402AW, dropping to only 281AW with the vent open. That’s about the same power as the Stihl SE 33 wet and dry cleaner, and a lot more powerful than the Shark CZ500UKT. This is a more expensive material than normal filters which is why you will mostly have to pay a bit more for a vacuum cleaner with a HEPA filter but the benefit is significant because you can be safe in the knowledge that it will capture and retain everything it takes in. How do you clean a HEPA filter?Henry Allergy has just one power setting but you can adjust the suction to some degree by swivelling a valve on the head of the suction tube. But here’s the rub… While the valve helps dial down the suction, there’s still way too much of it when used on a carpet, even with the bristles raised. It’s not terrible but it just takes extra effort to push and pull it across the carpet. Put another way, it doesn’t glide across carpet like a Dyson or a Shark. If you have access to another vacuum cleaner, use it to vacuum both sides of the filter. Make sure you clean all areas of the filter including the sides. This is an effective way to remove more dirt than just tapping off loose debris.
If you haven’t cleaned the filter for a while, you’ll immediately notice how dirty it’s become. The more dirt collected on the filter, the less suction your Henry can generate. To access the filter, you need to take off the lid of your Henry using the same method as when replacing the bag. But what does HEPA actually stand for? Well…. It depends who you ask but they all mean the same thing; less allergens, irritants and dust in your home. If you’ve cleaned a lot of dirt and dust from the filter, you might be surprised by how much more suction power Henry can now generate! When Should You Buy a New Henry Filter? With normal filters air passes through a sheet with holes and larger dust particles get trapped in the holes that are big enough to let air through but too small to let large dust particles and things like hair pass through.Tip: We recommend cleaning the filter outdoors. This prevents the loose dust and other allergens from being spread around your home. Step 2: Tap Off Dirt and Dust Unfortunately, Henry vacuum filters are not washable. Cleaning with water will cause any dirt and dust to become more clogged and reduce the suction power even further. Water could also damage the filter and cause it to perform less effectively. Can You Put a Henry Hoover Filter in the Washing Machine? HEPA Filters must satisfy a certain levelof efficiency. The HEPA (H13) filter in Henry Allergy is certified to clean, trap and eliminate particlesdown to 0.3 microns at 99.97% efficiency. That’s particles up to300 times smaller than a single grain of sand (90μm)! The only slight issue is that the metal poles do have a tendency to become stiffer over time and therefore more difficult to pull apart. I recommend you separate them at the end of every clean as a preventative measure. As Henry filters aren’t washable, they occasionally need to be replaced. Henry filters are widely available – just make sure you buy the right filter for your model.
How much dust stays inside the hoover depends on the kind of filtration system that it has and the better the filter the more dust that stays inside the vacuum cleaner and the cleaner your home is. A bag that’s more than 75% full may reduce suction. This is because the air must be forced through all the collected debris.Henry Hoover filters cannot be washed with water, as the dust and dirt will turn into mud. Start by tapping off loose debris into a bin. Then use a second vacuum cleaner to remove dust from both the inside and outside of the filter. Henry Hoover filters can’t be washed with water. Instead, you should remove as much dust as possible by tapping off the loose debris into a bin, then vacuuming the filter with another vac. If you don’t have another vacuum, then a soft (dry) brush can be used to remove dirt. Related Article: Where Are Henry Vacuums Manufactured? Frequently Asked Questions Can You Use Water to Wash a Henry Filter?
If you are prepared to spend a little more on a hoover with a HEPA filter then it will keep your home cleaner and fresher for longer. If your vacuum cleaner has a HEPA filter then it will keep hold of dust that is less than 1 micron in size. They will definitely keep more dust in your hoover than a regular hoover so if anyone in your home has dust allergies they will benefit from a HEPA filter. This is a premium compatible part that has been expertly designed for use in medical surroundings. Use around the home stops dust from re-entering the air. A god send for those with allergies.
Henry Allergy
The label under the handle on Henry, Hetty or Harry (or on the rear of your machine for James, Charles & George) will contain the model number. No, Henry filters should not be put in the washing machine. Water can clog the filter and they aren’t designed to withstand a wash cycle. Tip: Don’t have a spare vacuum? You can use a soft brush to remove loose dirt and other debris, although this won’t be as effective. Step 4: Replace the Bag All you need to do is remove it from the vacuum cleaner and run it under some cold water until you have visibly removed the dust that you can see.
Great Deal 
New Comment