Spares2go Heater Element compatible with Indesit IDC85UK IDC85SUK Tumble Dryer (2200W)

Product Information

So if your laundry is still damp or wet at the end of a dryer cycle, read on to learn the potential causes and solutions. Faulty Thermostats Locate the heating element. The heating element can be located at the rear of the dryer, level with the unit’s right side. Detach the two screws that connect the heating element to the dryer and let the panel glide out. After doing this, you should see three red wires, or leads, which are typically connected to the bottom of this panel on the left-hand side. Remove any build-up of fluff and lint, and then try to rotate the blower wheel by hand gently. If you feel the wheel wobble even slightly while attempting to turn it, you must replace the part. Reduce Drum Load Size If the thermostats are faulty, the dryer will only produce cold air or battle to control temperatures and cause the dryer to overheat. But when fluff and bits of lint get caught in the blower wheel, circulation is negatively impacted, and the tumble dryer will take longer to dry clothes. The Drum Is Overloaded

A heating element for a dryer is essentially a coil of wire that heats up when an electric current is passed through it. This heat is then used to dry your clothes. Heating elements can come in different forms depending on the type of dryer you have – electric, gas, coil, or infrared. B. Importance of a functioning heating element for a dryerThe thermal fuse is a safety installation that helps prevent the tumble dryer from overheating; the appliance won’t work when this fuse blows or trips. The blower wheel resembles a circular disc with indentations. The outer covering protects the disc and fan system of the blower wheel. Bear in mind that this part is sometimes crafted from durable plastics, while other times, a blower wheel can be made from corrosion-resistant metals.

In conclusion, a heating element is one of the most important components of a dryer, and choosing the right one is crucial for proper performance and safety. By understanding the different types of heating elements and the factors to consider when choosing one, you can ensure that your dryer is working efficiently and effectively. You need to set up and calibrate the multimeter as per the instructions, and turn the dial to the lowest ohm rating. Proceed to take the probes of the multimeter and place them on the relevant terminals inside the connector. The heating element is normally held in place with screws but could be held in with bolts on some older models. Use a screwdriver or pliers to remove them and gently pull the old element out of the dryer.

If your Hotpoint dryer takes longer than usual to dry laundry, there’s no need to panic. Because Hotpoint appliances are built to last, there’s a good chance you won’t need to replace your tumble dryer.

Instead of extending the drying time of the cycle and risking damaging the appliance parts, remove some garments from the dryer drum. Replace The Thermal FuseAs water is extracted from the clothes, it builds up in a reservoir at the bottom of the dryer. On the model shown within the video, the water is then pumped up into a container within the tray, where it should then be taken out and emptied. Remember, if you notice any signs of a faulty heating element, such as clothes not drying properly or burning smells, it’s important to take action immediately. This could mean replacing the heating element or calling in a professional for repairs. Finally, consider the cost and efficiency of the heating element. While it’s important to choose a high-quality heating element, you don’t want to break the bank in the process. Look for a heating element that strikes the right balance between cost and efficiency, and that will help you save money on your energy bills over time. How to Replace a Heating Element for a Dryer Coil heating elements are typically found in older dryers. They work by heating up a coil of wire that’s wrapped around a metal frame. One advantage of coil heating elements is that they’re relatively inexpensive and easy to replace. However, they can be less energy-efficient than other types of heating elements and may take longer to heat up. D. Infrared Heating Elements

Take off the heating coil panel. Using a screwdriver, take off the heating coil panel. Again, with a screwdriver, take off every screw lining the coil panel’s side, which resembles a metal box. While the suggestions above will help you fix a Hotpoint tumble dryer that’s not heating properly, it’s also essential to know how to clean and maintain your dryer to prevent these kinds of issues from developing in the first place. By following these steps, you can safely and effectively replace your heating element and keep your dryer running smoothly for years to come. Conclusion Allow the dryer to cool – The heating element can get extremely hot during use, so it’s essential to let it cool down before attempting to replace it. Clogged filters and vents are the most prominent cause of a blown thermal fuse. The Heating Element Is FaultyOnce you have the parts you might well be thinking what you need to do next - well, we actually have a helpful video that you can follow, as well as a written step-by-step guide, that will show you the process of these replacements - so you can repair your tumble dryer yourself (helping to save time and money on engineer call-outs) The first thing you need to consider is whether the heating element you’re considering is compatible with your dryer. Different types of dryers require different types of heating elements, so it’s important to choose one that’s specifically designed for your make and model. B. Wattage and Voltage You’ll need a few basic tools to replace your heating element, including a screwdriver, pliers, and wire cutters. D. Tips for Proper Maintenance Electric heating elements are the most common type of heating element for dryers. They work by heating up a coil of wire using electricity. One advantage of electric heating elements is that they’re easy to install and maintain. They’re also relatively inexpensive and energy-efficient. However, they can take longer to heat up than other types of heating elements. B. Gas Heating Elements Repairing a blown thermal fuse is impossible, and you will need to replace the part. Fortunately, replacing a fuse is pretty straightforward.