Airflow iCON 30 Extractor Fan 230V 100mm Outlet, White, 27 W

Product Information

The icon 72683501 is mains voltage(240v) IPX4 rated and is suitable for installation into zone 3 of a bathroom or toilet. It may be flush mounted in either the wall or ceiling and with a low profile fascia, sits unobtrusively in any room. With an air extraction rate of 76m3 per hour, it easily surpasses building regulations. When the iCONsmart is first powered on, you will hear the initial reset for 10-15 seconds. This is normal and will also occur if the fan is in its reset mode. App Control and Setup The PureAir Sense comes with two spigots (or sleeves): one for standard 100mm installation and another for larger 125mm portals. The larger spigot is the one to fit if you want to benefit from its excellent 39l per second flow rate. That said, its standard 32l per second flow rate is still better than most and easily good enough for the majority of bathroom installations. Do not use household cleaners containing abrasives. Cleaning of the internal parts such as the impeller should be carried out by using a soft brush. Never clean any parts of the fan assembly by immersing in water or using a dishwasher. Model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pull cord, Pull cord with adjustable timer, Humidity, pull cord with timer overrun, motion sensor with timer overrun, Motion sensor/humidity/timer . Don’t forget to add the control module you want. Only low voltage module fits low voltage fans. It/s so iCON easy Applications:

Model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pullcord, Timer, Humidity or Motion Sensing operation. Don’t forget to add the control module you want. Any module fits any fan. Its so iCON easy! Applications Airflow Developments Ltd shall not be liable for any loss, injury or other consequential damage, in the event of a failure of the equipment or arising from, or in connection with, the equipment excepting only that nothing in this condition shall be construed as to exclude or restrict liability for negligence. Full details at airflow.com/termsThe precise duration of the overrun is normally configured during installation, with most fans offering a range between 30 seconds and 30 minutes. You might as well tend towards the latter end of the scale as the cost is very low: on average, a fan like this uses around 8W. Most domestic bathroom extractors attach to a 100mm hole in the outside wall. If you’re replacing a standard-sized extractor fan, this hole will already be present and you should be able to install the new one yourself. Before you remove the old fan, it’s a good idea to take a photo of its wiring for later reference – and make absolutely sure you shut off the mains power before you take the old one’s front housing off. Make provision for the electric supply cable and wall plugs / appropriate fittings using the main body as a template. Level using guides below the L and R symbols. (see Fig. 6) If you don’t already have a fan, you’ll need to get in a qualified builder to make the hole and install the wiring. Be aware that there are regulations governing where your fan can be located: if you want to put a fan in Zone 1 (the area within a shower or 2.25m above a bath) or Zone 2 (60cm from Zone 1), it must be a low-voltage SELV fan with a transformer, or an AC-powered model that’s IPX5-certified. Most of our recommendations below are intended for use outside of Zone 2, but the layout of your bathroom may dictate your options.

Finally, if you think you (or anyone else in the house) will forget to turn the fan on, consider a model with a humidity sensor. This automatically activates the fan when the level of moisture in the air exceeds a certain threshold. This sensor may need occasional cleaning, though, or the accumulation of dust or grime will hinder its effectiveness. What about noise? This really is an excellent extractor that uses just 2W of electricity when running continuously and no more than 5W at full pelt. It’s also one of the most attractive models around – the fascia can be used bare or with the included white magnetic cover – and one of the very quietest.

Please note: While the Icon 30 uses 4" inch ducting it does require a 6" hole in the wall or ceiling for flush fitting. iCONsmart has several features included as standard and can also be fitted with digital micro modules to give a range of extra control options. Standard Features All electrical installation must be carried out by an approved electrician in accordance with Part "P" U.K. Building Regulations and to the latest IET standards, or the appropriate regulations in the country of installation. The iCONsmart 15 is IPX5 rated and therefore it is suitable for mounting in bathrooms (in zone 1 and 2).