Polishing Compound-Fine

Product Information

For the course compound I went against the scratch grain to cut down the hills. It took less than 5 minutes of this motion to see a difference then I swirled for another few minutes. The course compound usually has had enough when it begins to cake, as in the picture. Don’t fret, we’ll look after that in a jiffy.) Dried Compound on Part with Applicator For some modelers this would be enough shine, but there are a few more steps left to get better results, so hang with me till the end. As you can see there is a drastic improvement and with just one application. Also note, I’ve washed the part and applicator. Almost Mirror Finish with Applicator and Tube Behind I should have asked OP how bad was his "Orange Peel of Doom." Old people tend to make assumptions, and I thought of my own novice mistake from 20 years ago. It has the classic orange peel. (Scout's honor! I'm not this bad anymore, I hope... but everybody starts as a noob.)

Now let’s have a look at the part after drying for 48 hours. It’s vital to let your painted parts cure for no less than 2 days, yet I’d strongly recommend a week or two even. You can see the glossy shine is gone and many micro scratches came through. There are 3 coats of paint on this bonnet so you have a choice. You can polish now, and hope to reach the level of the valleys, or you can clear coat. Please consider clear coating, it’s far less messy, hence why I did. Near Mirror Finish of Part Resting on Blue Glove I did not got an answer for wich Tamiya polish I should use. I saw that they sell three different kinds and I think that it is for the shelf queens. Is it possible to use just one for an ok result? H.G. Barnes is a former voice-over artist and retired sales and marketing professional. He’s the author of two large volume science fiction adventure romance novels with many more in the works. For well over 40 years he’s been building scale model replicas and now does commission work for clients in Canada and the USA, plus completes projects for companies in Asia and Europe.

Why us

Then go finer, like 1000. Usually 1000 is enough for my bashers. But if you want more, you can use 1200 or 1400. I don't think going beyond 2000 is meaningful. As the paint solidifies, the paint surface is what makes it smooth. Even if you make it as sooth as the reflective surface of Hubble telescope, it won't matter. The reason why I still do 1200 or 1400 sometimes is to make sure that 1000 grit did not miss 800 scuffs. So 1200 or 1400 is like a quality control for me. 2000 would be extra nice. As you can see by the spot on the applicator that it doesn’t take much compound to cover the work area. Close Up of Compound Part and Applicator

It took only a few drops and two applications to get the result you see in this shot. Very simply, you rub it on, wait a few minutes for it to dry, gently polish then rinse and repeat. The results are stunning. Super Mirror Finish with Silver Cloth Besides First, begin with one of the higher grits of polishing sander or polishing cloth that will “cut” a layer of coating to take the top off the lint and dust. I use a swirl motion and gently rest my 3000-grit polisher at each spot, do not push or add force. Use your finger to feel the result and when you’re happy gently polish the entire area in one direction with a higher grit count. It sounds like a lot of work, but even 20 or so swirls and passes will make a huge difference. Being long winded is for explanation. Half Sanded and Half Taped Part I hate when that happens. Orange peel happens when there wasn't enough time for the first layer to dry. I just experienced it myself. Lacquers dry fast, but I still managed to make a zombie lady. Sorry about the slightly out of focus shot, but you see the marks have been erased and another coat of primer added. I bought a can of Tamiya TS-9 British Green for the model and because dark colors show flaws. TS-9 with a Clean Primed Part At this point you can choose to reapply the course compound or move on. It depends on your theme and desired look. Make certain, though, you wash your applicator in the warm water. Takes but a few seconds and ensures what is put on it next is not contaminated by the previous job. Rinsed Off Part with Course Compound Behindmy objective is to get a nice glossy shine on my car body like I’ve seen people get on YouTube by using it. They tend to sand the body first with 6000/8000 grit sand paper For demonstration I’m hoping for flaws to show you. Now these spots can be sanded smooth again. I’m going to reduce my second primer with Mr. Leveling Thinner 400 because it self levels. Here’s a tip, find a cover for your part to prevent unwanted dust or lint from gathering on it. Mr Leveling Thinner 400 with Flawed Part The final Tamiya application was with their Finishing compound. Here I did 2 or 3 applications to get a mirror finish. If you look closely, you see the reflection of my glasses and finger at the bottom of the polished part. It’s quite remarkable the look you achieve with not much effort. The great thing about Tamiya’s Finishing Compound is that it can be used for any general polishing, such as removing fingerprints or getting rid of water marks around decals. Fine Compound with Applicator and Silver Labeled Tube

This article will focus on Tamiya Polishing Compounds and how we get to that point, so let’s grab a bunch of items from the store and have some fun. Many Items Gathered Together I'm afraid 2000 will clog up right away. (Also, it would take forever.) I would try #800 or so and see how it goes. It depends on how much paint needs to be removed. You can start with 800, but I have a feeling that's too fine. There is no set rule, so you would have to judge as you sand. Coarse grit (like 600) will get things done faster, but you don't want to leave deep scratches. So starting with finer grit than you think you'd need is a better idea. If it takes long, you can go slightly rougher to do the majority of the sanding done.Getting a mirror finish takes a bit of effort, yet when you see the results I’ve shown it’s more than worth the minimal amount of elbow grease. Talk about gratification. All the products used in this article came from Sunward Hobbies. I didn’t use any special materials and all the techniques can be easily replicated by most people. In this Sunward Hobbies Tutorial, you’ll be seeing how polishing your model with Tamiya Polishing Compound can make a huge difference. Also, I’ll throw in some items which will make your life easier, give an even better finish and possibly save you some money.