Osmo Decking Oil Colour: Grey 019 2.5 litre Tin

Product Information

Ipe: 6-8 weeks exposure. 006 Bangkirai is optically suitable and a very popular choice of colour tone. If possible, and if the wood is absorbent please apply the first coat to all sides before installation. When you start adding a little colour, the factor increases, so a light or natural oak for example will bring you up to a 20 – 30 factor and then a dark oak, rosewood, or dark brown will bring you up to a factor 50. This is the best way to maintain the natural colour of the wood over time, but of course if you don’t want to add colour then a clear oil with UV stabalisers will require annual top up. If you keep up with regular maintenance there should be no need to retreat with the reviver, but if you do need to use it again in the future the oil will need to have worn away or you can use a pressure washer to remove the last of it.

If the finish is an oil it should have soaked into the surface of the wood and will naturally wear away over time, it will not peel and flake unless it has been over applied.Oils can not be removed with a stripper, some lift will come from using a pressure washer, but take care not to hold the nozzle too close to the woods surface as this will damage and splinter the wood. For the following wood types, a weathering period is recommended. Depending on wood species, new or freshly sanded wood requires up to 12 weeks (approximate) exposure to the exterior elements before application. Rosewood: 4-6 weeks exposure. However, Natural Oil Woodstain 727 Rosewood is optically suitable and requires a weathering period of approx. 12 weeks before use of Natural Oil Woodstain.I am sorry for the delay in response, it is a super busy time here at Wood Finishes Direct. A stain or paint is a surface sealer and is likely to, over time, peel and flake, if the treatment appears to be lifting it is likely that this is the finish you have and this can be removed with a pressure washer or stripper product such as the Paint Panther Paint and Varnish Remover Oil is also really durable and is easy to maintain – you just need to keep it clean and touch it up every now and then. It’s very resistant to dirt and water so doesn’t require much upkeep at all.' As you have a dog I would recommend considering an oiled finish, this will be far easier to maintain over time, oils soak into the wood surface and so is less likely to be effected by claw marks, and even if it is, you can simply patch repair and the oil will blend well. Oils are also easy to maintain as they wear, simply ensure the surface is clean and dry and then you are able to apply a top up coat when needed, usually around 1 or 2 years down the line, depending on use.

Always, stir the contents of the tin thoroughly, at least for a couple of minutes before applying. This ensures that colour pigments and other important ingredients of the product are well distributed and not concentrated at the bottom of the tin. My advice would be to leave the floor treatment free as you are putting vinyl down. As it is an internal area preservative are not really recommended or required. Its not wise to apply an oil and then cover it with any floor covering the wood does not require protection. Only apply in double figure temperatures and when the weather is set to be dry for at least the minimum drying time displayed on the tin. Single figure temperatures, damp or wet conditions could adversely affect the application and final finish of the product We recommend using the clear version, as it delivers a beautifully natural finish. The same can't quite be said about the teak colour, as it's a little orange.Thoroughly clean or lightly sand old microporous stains or completely remove old varnishes before application. If any sanding works are carried out some fresh wood species must be weathered as directed above to improve absorbency once more. Sanding to finishing grades of no more than a P120 grit are recommended. Always wear a dust mask when sanding. This depends on your home's exterior and the colours and tones in your garden. Avoid anything jarring, and look to either complement or contrast with your walls and fences. Resinous wood, such as Larch or Douglas Fir, needs to weather off for at least 6 weeks to improve absorbency. Pressure impregnated wood and tropical species like Massaranduba, Bangkirai, Garapa, Iroko need to weather off for at least 3 months. Cedar requires a 3 month weathering period to improve absorbency.

The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. An oil soaks into the surface of the wood and will wear away over time. A stain, paint or varnish is a surface sealer and over time could peel and flake, exposing bare wood underneath. Paint, stains or varnishes can be removed with a stripper such as Paint Panther Paint and Varnish Remover. Oils unfortunately can not and if you can’t wait for them to wear away naturally the you can use a pressure washer to remove much of it, care must be taken not to damage the wood however. Bangkirai: 12 weeks exposure. 006 Bangkirai is optically suitable and a very popular choice of colour tone. Thank you for getting in touch with your question. It is a common question asked for beautiful tropical hard woods such as Ipe, Balua and Iroko. Jatoba is a less common one, however if it is anything like the others it will require a period of weathering. Tropical hardwoods tend to have a naturally high oil content when they are relatively new, these oils will prevent the uptake or adhesion of any product that you try to apply. So a weathering period to allow these oils to naturally disperse is the recommendation. Balau: 12 weeks exposure. 006 Bangkirai is optically suitable and a very popular choice of colour tone.Staining can provide more colour options than oiling, but it can be more difficult to maintain and may require more frequent refinishing. However, oiling is often easier to maintain and when using a clear finish will offer a more natural look. In addition, oiling may not provide as much colour variety in comparison to staining. After the weathering period, it is generally recommended to clean the surface from the extractive content. Osmo Wood Reviver Power-Gel can be used to refresh the colour of the wood. If necessary and before application, de-grease the dried surface with Osmo Brush Cleaner and Thinner (degreaser), always trial apply! Stir the contents of the tin thoroughly before and periodically during use and especially so with coloured oils It would need a little bit of experimentation first to get the right result, it may be that you only require a very small amount of the coloured oil added to the clear, it is vital to thoroughly mix them together. So small ratio measures first and tests on your wood, until you get the desired result and then you are able to mix up a larger quantity in the same ratio to complete the project. This will help you to control the colour a bit more for getting the lighter result.