Configuration and firmware update FOTA Web, FOTA, Teltonika Configurator (USB, Bluetooth), FMBT mobile application (Configuration) Status info enables the user to monitor real time information of FMB920. Following fields are displayed: Device Info, GNSS Info, GSM Info, I/O Info, Maintenance and etc. User is able to export all of the information to .HTML file using icon which is at the top right corner of the Device Info area. GPS Satellites Quantity – is value of minimum visible satellites available to device to renew GPS data after fix was acquired. Configurator suitable for: FMB920, FMB900, FMB910, FMB001, FMB010, FMB110, FMB120, FMB122, FMB125, FMB130, FMB202, FMB204, FMB962, FMB964, FM3001, FMT100 CONFIGURATOR VERSION More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.

This message contains information on how to operate FMB920 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device! If the device is in GPS Sleep or Online Deep Sleep mode, sent SMS/GPRS message will arrive to the device. Default log capture time, accelerometer capture time and files directories can be changed by pressing icon at the bottom right corner. Important! If Auto calibration is disabled, the device should be mounted according to the User manual for EcoDriving feature to work properly. If enabled, AXES will be reoriented to VEHICLE axes according to the User manual (+X – Forward, +Y – Left, +Z – Down). Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip

Dump files can be read only with special software. If needed, provide these files to your Teltonika sales manager or Teltonika Support team. Added possibility to set LV-CAN200, ALL-CAN300, CAN-CONTROL program number using SMS command in Online Deep Sleep mode Accelerometer - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF; There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. FMB920 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality: If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose. Because our solution is developed in-house, if there’s functionality that isn’t in our system that you require, please get in touch and we will aim to accommodate your requirements.

Gravity filter subtracts gravity from vector when devices are calibrated or if auto-calibration is disabled (default values). Gravity is only removed when gravity filter is enabled. Power off sleep mode can be described as the lowest possible power consumption mode where the device can go into power off state. This document describes FMBXXX platform devices firmware improvements, changes, new features implementations as well as current firmware release version. Changed odometer configuration parameter available min value to 0, while on TCP configuration values is from 1 Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +6..+30V DC. Note: In FMB920 devices autocalibration is set by default and it is not configurable via configurator. Device connected to OBD port is not positioned according to the vehicle axis and in this case autocalibration is a must.

Accelerometer - after the button is pressed, the device starts to capture accelerometer values for 1 second. Ignition status is used in power management and the following functionalities: Eco/Green Driving, Excessive Idling, Fuel Consumption, Over Speeding, Towing Detection and Trip. Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires. LLS calibration - in this section you can calculate calibration values of Analog LLS sensors for AVL server - create a polynomial which is needed to convert sensor values to liters: Calculation formula - ("GPS" + "GLONASS" + "Galileo (0-sat)" + "BeiDou (0-sat)") / 2 (four GNSS systems)**Improved SMS/GPRS command "setdigout" with speed parameter according to documentation (do not trigger DOUTx if GNSS FIX unavailable) After that, the time difference is still calculated, but the difference is expected to persist for at least 5 minutes to trigger a GNSS time re-synchronization. YY – branch number, shows major changes in firmware, i.e. new module support added or new major feature added. If there is no GNSS fix, the accelerometer determines profile change. If there is no OBDII dongle active (or speed reported by dongle == 0 km/h) accelerometer determines profile change.