PROVIDES A WATERTIGHT SEAL. The perfect product for a leaking basement wall or building foundation works by creating a watertight seal to keep moisture away. Stormseal is a water-based aqueous styrene-acrylic type polymer dispersion seam sealer. The liquid soaks into pinholes and leaking seams and dries clear, leaving a flexible and impermeable waterproof surface. Nanoman Raw Timber is a high-performance, nanotechnology enabled, penetrating sealer for the protection of all types of unpainted timber. It is a clear, colourless, breathable, abrasion-resistant, easy to clean, waterproofing coating designed to protect these surfaces from water damage, stains and marks caused by liquid spillages, food stuffs, and external pollutants such as dirt, bird droppings and leaf staining. TRANSPARENT PROTECTION. The Waterproof Invisible Nano Sealer is transparent, which allows for waterproof protection while having no aesthetic change. Do not use chlorine, bleach, sodium hypochlorite, acid, Paveclear or Paveclean chemicals on surfaces intended for Invisible sealer Nano

Nanoman products are designed to cut your cleaning time significantly and eliminate the need to use aggressive cleaners that are harmful to our environment. Aggressive chemical cleaners will actually reduce the lifespan of the Nano coating. We recommend cleaning only with water and wipe down with a soft cloth or towel. Marks can be removed by dabbing the area with a damp cloth. Do not rub vigorously or scrub the mark with a stiff bristle brush. For larger outdoor areas, you may use a high-pressure hose, (set to the lowest pressure possible), however we caution against over use as this will eventually reduce the lifespan of the Nanoman coating.SAFE & NON-TOXIC. It is formulated with odorless and non-toxic substances. It will not damage surfaces and will not cause pollution. Nanoman Raw Timber is recommended for use on raw or untreated timber only. It will work on stained timber however the effect will not be as good due to the change in the characteristics of the surface. It is not recommended for use on painted timber surfaces.

Ensure application is from bottom to top on vertical surfaces taking care not to let the product run. Nanoman Raw Timber has been designed to protect raw timber against water damage and decay whilst allowing it to age and grey naturally. With its hydrophobic properties, Nanoman Raw Timber ensures the integrity of the timber is preserved by inhibiting rot, mould, moss, algae and mildew growth. Once applied, the microscopic nano-particles form an invisible protective layer that creates a water repellent surface as well as penetrating into the pores of the timber to provide long lasting protection. Yes. Nanoman Raw Timber can be used on any raw timber surface both inside and outside the home and is perfect for protecting your brand new or used kitchen bench top. This sealant has been certified as food safe and is therefore ideal for use in food preparation areas.Use brush supplied to apply as a film directly onto and covering the seam stitching or hole. Stormseal will soak into the stitching or hole. Allow to cure for 15-25 minutes or until clear and dry. If you are in an environment that produces a lot of friction against the coated surface i.e. a windy desert or seaside location, its life span may be shortened. Foot traffic will also lessen the life span of the sealant. Respiratory Protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.

EASY TO APPLY - No primer is needed prior to the application of waterproof invisible sealant. Apply immediately for instant waterproof protection. Clear the affected area of moss and debris and remove any surface water, oil or grease. As Sealers Direct has no direct control over the methods employed by the user in applying its products, any warranty either written or implied is given in good faith and can only cover the material itself applied, to ensure 100% performance efficiency. This varies with substrate, and treating a small trial area is recommended to calculate true consumption. DON'T LET WATER DAMAGE RUIN YOUR SURFACES WITH THIS INVISIBLE WATERPROOF SEALANT. ONE COAT WILL LAST FOR AGES. Are you looking for a solution to the leakage problem? Waterproof Invisible Nano Sealer is a rubberized paste that effectively seals and protects broken surfaces. It's a liquid sealant that is a paintable and waterproof wide variety of surfaces.

It provides a rigid but flexible layer of protection to the applied surface. It is leakproofand can be used on wet surfaces with high bonding strength. It is transparent and has a non-yellowing substance. Re-application: Subsequent applications MUST be applied “wet on wet” within 10 minutes of previous application. All surfaces should be porous, clean, dry and free from loose debris, flaking material, dust, dirt, grease and vegetative growth. ENDLESS POSSIBILITIES. This nature-friendly product allows for endless possibilities of usage. Use for roofs, gutters, planter boxes, ponds, sheds, mobile homes, metal, wood, concrete, and more.