Generally, the guide or pilot bit is just used to get you started and keep the actual core bit in position whilst cutting into the surface of the wall. Before you start your drilling you should always make sure there are no cables or pipes hidden in the wall at the spot you intend to drill your hole. When drilling your hole, always hold the drill and core bit dead level. You do not want to drill in at an angle and cause the hole to slope up or down! Once you have cut 25-30mm into the surface you are working on, you can withdraw the core bit and remove the guide drill and carry on without it.

As this point it’s a good idea to ask someone to stand on the other side of the wall and let you know as soon as the guide drill breaks through and when it does, stop drilling. With the above in mind, dry cutting diamond core bits are generally used when working indoors, whereas wet cutting bits are used externally. The drill bit itself features carbide “teeth” that surround the circumference of the drill bit. Once rotating, these teeth bite into the surface you’re working on and cut their way through creating the required hole.

You can only compare up to four products at a time.

Essentially the speed that you drill at will be dictated to you by the size of hole you are drilling. As a very general rule of thumb, the larger the hole you are drilling and the denser the material you are drilling through, the slower the speed you should drill at. When hiring or buying a core bit always make sure you have the correct size and type of arbor for not only the core bit your are using but also for the type of drill you have e.g. SDS, spline, straight shank etc. If you keep forcing the core cutter through, when you actually break through you will force a large amount masonry away from the outside of the hole, making a total mess of it all. With everything assembled it’s time to start drilling your hole. Position the tip of the guide drill on your drilling mark and start the drill slowly, increasing speed slightly until the pilot drill starts biting into the wall. With the drilling point clearly marked on the wall, next setup your core bit and drill. Screw the arbour into the end of the core bit until it’s pinch tight.

There are a few different types of core bit and the best one to use will very much depend on the size and depth of hole you’re drilling and the type of material you are drilling through. If in any doubt always refer to the manufacturers instructions for your particular power drill and also for the core bit you are using. In both cases, each set of instructions should state the correct drilling speed you should be using. Preparing for Drilling Holes Using a Core Drill For the neatest cut and finish to your hole it is advisable to then finish the hole from the other side. This guarantees both a neat entry and exit hole. Due to the amount of heat created during the drilling process it is necessary to keep diamond core bits as cool as possible to prevent unnecessary damage to the cutting teeth to a minimum. If the surface of the cutting teeth are subjected to too much heat the metal encasing them melts covering the diamonds and reducing cutting efficiency. If this happens the drill bit then needs to be “redressed” to expose the diamonds once more.

What is a Core Drill?

Corded power drill with safety clutch and variable speed ideal for use with a core drill How Fast Should you Drill When Using Core Bits?

If you are able to drill right the way through the wall in one go, the core drill will remove the core at exit. A core drill should always be used with a power drill, at minimum around 800 watts and at maximum somewhere around 1300 watts. Your chosen drill should also have a variable speed function (somewhere between 100 and 300 rpm) and it must also have a safety clutch!

Sign up for special offer emails

Once the core bit is attached to the arbour insert the pilot or guide drill into the arbour, pushing it in until it goes tight. Before you start any drilling, the first job is to measure and mark the exact spot that you want to drill your hole so there isn’t any mistakes. There are in fact two different types of diamond core bit – wet cut and dry cut. Essentially, wet cut diamond core bits use water to cool them while drilling and dry diamond core bits are just used dry.

As we have already stated but will do so again, never use hammer action when core drilling. The drilling action needs to be as smooth as possible and the jerky action of the hammer can snap expensive diamond teeth very easily. Mark the Exact Drilling Spot Diamond core drill and correct sized arbour What Type of Power Drill do you Need for Core Drilling?If however the depth of the hole is longer than the drill bit you will need to withdraw the core bit when you hit a depth of about 125-130mm and chop out the core with a hammer and bolster, or in some cases you can lever it out. If you don’t already have a suitable drill, any decent hire company will gladly supply not only the correct drill but also the correct diamond core bit, if purchasing either the drill or core bit is deemed too expensive. Remember you will also be charged for the amount of wear on diamond tipped bits. You can never take it for granted that work hasn’t been done by someone else in this area before and it has not been recorded. When using dry cutting bits it is essential that they are kept as cool as possible. To do this they should be used in short bursts and the whole bit should be regularly withdrawn from the hole and exposed to the air to disperse any heat. Despite this, dry cutting diamond core bits don’t have to be used dry you can also use them wet. With the drill held straight and true, keep drilling, stopping regularly and withdrawing the bit from the hole to allow it to cool down. When withdrawing a core bit from a hole ensure that it is still rotating.