GHz which was a single core), and with more recent hardware (macchiatobin with A72 at 2 GHz), I’m doing 19 Gbps on two 10G ports. Combining FriendlyWrt and an internal SSD, you can use the board as a NAS server to back up your local data.

Open source and programmable] It can support FriendlyWrt, a custom system based on OpenWrt distribution. You could establish another subnet via DHCP on your NanoPi, then it would be the gateway of the connected clients. It’s not a matter of ISA but only a matter of crappy ethernet controllers found on cheap low-end devices, and/or attached to a low-bandwidth bus (iMX6 anyone?If I do tcpdump -i eth1 port 67 or port 68 -e -n -vv on the DietPi, I can see the DHCP requests coming from the laptop. I found it hard to measure consumption with more complex scenarios just with a primitive meter only outputting actual amps/volts. Major downside: you need a lot of patience since after adjusting settings it requires a long(er) time span for the new averaged consumption value to settle.

According to another review relying on one of those unreliable USB powermeters R5S in idle generates a 3. Audio ports : - Phone ports : - Serial : Yes Serial connection parameters : 1500000 8N1 Serial connection voltage : 3. With Allwinner’s BSP kernel the defaults (both cpufreq governor and parametrization) led to both iperf task and interrupt processing ending up on cpu0 while staying on the lowest cpufreq OPP 408 MHz for a long time or even during whole iperf execution. FriendlyELEC's NanoPi range is receiving a refresh with the launch of the NanoPi R5S, a single-board computer boasting two 2. The Rockchip RK3568 processor is covered with a thermal pad that’s in direct contact with the metal enclosure for optimal cooling.It involves RPS: set_interface_core 4 “eth1-0” set_interface_core 4 “eth1-16” set_interface_core 4 “eth1-18” echo b > /sys/class/net/eth1/queues/rx-0/rps_cpus I. just suggesting it might be useful (several github sites, this), if tables increase in size (low, high, mean/mode/median [(n) values first]). In general I’m also curious whether R5S can be powered by a dumb 5V power source or a USB PD capable charger is needed. When the software I run (mostly helt back by OMV) gets bookworm support I see no reason to keep the Debian 11 with (6.

If your main network is IPv4, and NanoPi-R5S works in IPv6, the computer may not be able to connect to the Internet.According to iperf3 test speeds, shouldn’t I reach at least 250 megabyte file copy speed per second? likely not the fault of this unit – I think I just picked a bad source for graphical desktop interface? All interfaces acquired IP addresses properly at boot time with DHCP, and the devices on the LAN can also be accessed with . Meanwhile I overwrote Android with the latest OpenWrt – more on that later but as you’ll see above, OpenWrt originally was just fine. For official OS, you need select the file with the filename containing '-sd-', for example: rk3NNN-sd-friendlywrt-21.

Since then, the range has received a few upgrades — the most recent being the NanoPi R4S, a dual-gigabit design with a Rockchip RK3399 six-core CPU. That is, as always, clearly marked on their WIKI I mentioned above, along with full specs – they are good at that kind of documentation.com/drive/folders/1yWLtwCesnHfoM8DG7NgJ4jZrjRSI-dQs Installation method(s) : SD card Comment installation : SDcard and eMMC images available on FriendlyElec Recovery method(s) : SD card Picture : Comments : FriendlyWrt oem distro is based on OpenWrt 22. When I connected power to the unit and HDMI (the unit supports 4K60p video) – the console came up wth LOGIN… that’s in the WIKI. After playing a video, enter about://media-internals in your browser's address bar to check if hardware decoding was enabled for the most recent playback.